For the best results, purchase pre-primed boards whenever possible. Lay trim boards across a pair of sawhorses. Use a brush, roller, sprayer, or some combination of all three to paint your boards...
Cut a few braces from 4- to 6-inch lengths of scrap baseboard and put 45-degree angles on the ends. Apply construction adhesive at the top and bottom. Nail the floor trim to the studs and then tack the braces to the trim with 1-inch brads. Force the gaps closed with the scrap and tack the blocks to the trim.
Drag the compass point along the floor, ding a line across the bottom of the baseboard. Remove the board and set it onto a cutting surface. Set the circular saw blade depth to the depth of the board, and on a 5-degree bevel with the face of the cut toward the wall. Trim the board along the penciled line.
Protect your workplace floor with drop cloths, move in a pair of sawhorses, and set your trim pieces in place so you can stain, prime, and/or paint them all at one time. Once the paint has dried, it's time to install the molding.
Floor trim allows flooring to neatly fit next to wall, and needs to be replaced every so often due to wear and tear. Replace your floor trim quickly with hel...
Before you install new baseboards, remove any existing trim, then measure the perimeter of the room. Start by measuring and cutting your outside corners into miter joints, or 45° angles that will match up to form a 90° angle. For inside corners, you can either miter them or cut one board to a 45° angle and use that to cover the other board.
Cut an Inside Corner Joint A coped joint is used where the baseboards meet an inside corner joint. To make a coped joint, butt one piece of baseboard flush against the wall at a 90-degree angle (as in the previous step). Next, lay the other baseboard molding (that will join the one already in place) face-down on the floor.
Pry off the old baseboard carefully with a small pry bar so you can use it to mark and cut the new molding. Protect the wall as you pry off old molding so it won't be damaged. Use a piece of scrap wood between the wall and the pry bar. You may be able to cut off damaged areas of molding and re-use part of the old molding.
Much like the tile-to-laminate strip, this one reduces from a higher tile floor covering to a lower vinyl floor. In almost every case, vinyl will be lower than laminate. Installation involves anchoring a metal channel to the subfloor using screws an expansion anchors, then snapping the top strip into the channel to cover the seam between floors.
How to Install Baseboards. Maybe we are getting ahead of you. Perhaps you don’t have any baseboards at all? No worries, ‘DIY Advice‘ shows us how to install baseboards, and it is easy. Remember, the wider (or taller, depending on your perspective) the baseboard is, the more modern and upscale it looks.
How to Install Vinyl Plank Flooring as a Beginner!See my flooring install playlist: http://bit.ly/2uFkWp6Thanks to FilterBuy.com for sponsoring this video! C...
Begin the first row of flooring by placing the planks with the tongue side facing the wall. Install the second plank next to the first by aligning the tongue into the groove and press the plank down to snap it in place. When you come to the end of the first row, cut the length of plank needed to complete the row.
Slide the compass along the floor over the board's length, keeping the points aligned vertically. With a circular saw set for a 2- to 5-degree bevel, cut alongside the scribe line so the face of the cut will be on the side toward the wall. Trim the beveled edge down to the line with a block plane.
Score perimeter of trim, where trim is bonded to adjacent surface(s). Pry trim away from surface without damaging adjacent surfaces, finishes or hardware. Remove trim millwork from premises. 132 linear feet: $114.21: $172.29: Molding Debris Disposal Costs to load and haul away old materials, installation waste and associated debris. 132 linear ...
Cut one end of a piece of baseboard at a 45-degree angle with a miter saw so the longest part of the board is on the back against the wall. Measure the length of the wall from inside corner to...
T-Molding - Doorway molding used to join two wood floors or floors of the same height such as ceramic tile, hardwood, or laminate, in adjoining rooms. T-Molding are also used to provide expansion joints when a floor dimension exceeds the length or width of 40'. Installation: A space of 1 1/4" between the two adjoining floors is necessary to properly install the molding.
Install the carpet – Install the carpet all the way against the wall. You don’t need to leave any gaps. The trim will be installed on top. Cut the baseboard – Get your baseboard cut to the exact length of the space you’ll be putting it.